---

Epoxy.com Product #26HP

High Strength, High Performance Epoxy Grout

---

DESCRIPTION

Epoxy.com Product #26HP is a high strength, non shrink, 100% solids epoxy grout. Epoxy Resin and specially formulated aggregate produce a fluid, non shrink precision grout. Units are preproportioned for ease of mixing and use on the jobsite. Epoxy.com Product #26HP has superior handling and physical characteristics when compared to conventional epoxy grouts.

ADVANTAGES

• Epoxy.com Product #26HP is simple to use. Premeasured proportions allow for precise and repeatable results.
• Epoxy.com Product #26HP is insensitive to moisture and may be used on dry and damp substrates.
• Pourable consistency - flows easily, self-levels in base-plate forms, anchor bolt holes and floor toppings.
• Formulation permits placement up to three (3) inches thick.
• High strengths - 12,000 psi compressive strength in twenty-four (24) hours at 73°F; ultimate strength averages 17,000 psi in twenty eight (28) days.

WHERE TO USE

Epoxy.com Product #26HP is used to seat and support reciprocating machinery and other equipment where heavy loads, impact, torque and other operating stresses occur. Typical applications include:

Transportation Grout Pads Anchor Bolts Crane Rails

Industry Crushers Millers Blowers Lathes

Utilities Generators Steam Turbines Transformers

PHYSICAL PROPERTIES

Mixing ratio of Epoxy.com Product #26HP Resin only - 100 A to 16 B by weight

Working Life - Mixed Grout (Filler In)
Temperature	Time
45°F	100 - 120 minutes
70°F	50 - 75 minutes
90°F	30 - 45 minutes
Compressive Strength: ASTM C-109
	40°F	70°F
6 hours		3,000
8 hours		6,500
16 hours		8,500
1 Day	8,000	12,000
3 Days	9,000	14,000
28 Days	14,000	17,000
Tensile Strength:    ASTM C-190, 7 Day		2,400 psi
Shrinkage:    ASTM C-827-82		(+0.1% expansion)
Flexural Strength:    ASTM C-580		5,000 psi
Flexural Modulus:    ASTM C-580		1.4 x 106 psi
Bond to Concrete:    ASTM C-882		substrate failure
Coefficient of Expansion:    ASTM C-531		16 x 10-6 in/in
Creep ASTM C1181    less than 0.3%		Loading 500 psi, 80°F
Shelf Life		1 year

SURFACE PREPARATION

Proper preparation of the substrate and the contact area of the base plate is essential. Substrate must be both clean and sound. Remove laitance, oils and grease from concrete by sandblasting or bush hammering. If possible, sandblast bottom of base plates and wipe clean and dry. Apply grout as soon as possible after cleaning steel surfaces to prevent recurrence of oxidation. (If corrosion resistant primer for steel base plate edges or top surface is required, use Epoxy.com Product # 1200 - Epoxy Zinc Rich Primer.)

MIXING

Initial mix temperature must be 50°F minimum. For best performance, mix entire pack. Pour B Component into pail of A component. Mix for two (2) minutes with low speed mixer until uniform. Scrape sides and bottom to ensure complete mixing, avoid entrapping air. Slowly add filler while continuing to mix resin until all is added or desired consistency. Mix additional one (1) minute and place grout.

If less than full unit is required, carefully measure 100 parts Component A and 16 parts Component B by weight and add desired amount of filler. Do not thin Epoxy.com Product #26HP. Solvent will prevent proper cure, and may cause shrinkage.

APPLICATION

Construct containing form with head box, if necessary. Any form surface in contact with Epoxy.com Product #26HP must be coated with release agent. Seal forms tightly to prevent leakage. Leakage that causes grout in place to subside below plate bottom level will cause loss of contact and voids at grout/base plate bottom interface. Re-establishing complete contact will be difficult at best. Be certain that all tools and mixing materials are at hand prior to mixing of Epoxy.com Product #26HP.

Mix Epoxy.com Product #26HP in accordance with mixing instructions. Pour grout into form from one side only. Pour continuously while maintaining a minimum of one (1) inch of head above the base plate bottom until grout appears full width of the base plate at opposite side of the form. Continue pouring at a reduced rate until Epoxy.com Product #26HP levels at 1/4" above the plate bottom on all sides. Clean equipment with MEK, Xylene, or similar solvent before Epoxy.com Product #26HP hardens. If placement depth exceeds three (3) inches, contact Epoxy.com Technical Service for assistance.

PACKAGING

Epoxy.com Product #26HP is conveniently packaged: "A" Component in a 3.5 gallon pail; "B" Component in a 1 gallon jug and four (4) 50 lb. bags of "C" Component. Yield is 1.75 cubic feet per unit at 4 bags "C" Component. Five (5) bags may be used for economy but will result in very stiff grout. Yield with 5 bags is 2.0 cubic feet.  Note: This product is not a stock item and is made to fill each order as it comes in.  Please allow up to 2 weeks for manufacturing.

SHELF LIFE

2 years

CAUTION

"A" Component contains epoxy resin. DANGER! "B" Component contains alkaline amines; strong sensitizer. May cause skin sensitization or other allergic responses. Use with good ventilation, particularly if material is heated or sprayed. Prevent all contact with skin or eyes. Wear protective clothing, goggles, gloves and/or barrier creams. Keep container closed when not in use. Wash thoroughly after handling.

FIRST AID:

In case of skin contact, immediately wash with soap and water. In case of eye contact, flush eyes with copious amounts of water for at least fifteen (15) minutes. Remove contaminated clothing shoes. If irritation persists, seek medical attention. Wash clothing before reuse.

FOR INDUSTRIAL USE ONLY. KEEP AWAY FROM CHILDREN.